|
|
|
 Product Hydraulic Cylinder |
|
|
 |
|
|
1T |
2T |
3T |
4T |
5T |
Inside Cylinder Diameter(mm) |
¥Õ63 |
¥Õ90 |
¥Õ110 |
¥Õ125 |
¥Õ140 |
¥Õ45 |
¥Õ65 |
¥Õ80 |
¥Õ90 |
¥Õ100 |
|
70kgf/§²(6,865MPa) |
Maximum Working Pressure |
Load:150kgf/§²(14.710MPa) Head: 90kgf/§²(8.826MPa) |
Inner Pressure |
Load:210kgf/§²(20.594MPa) Head: 140kgf/§²(13.729MPa) |
|
Load:3.5kgf/§²(0.343MPa) Head: 2kgf/§²(0.196MPa) |
|
0.06m/min(1mm/sec) |
|
10m/min
(166mm/sec) |
9m/min
(150mm/sec) |
8.4m/min
(140mm/sec) |
7.7m/min
(128mm/sec) |
7.1m/min
(1mm/sec) |
|
The Range of Working Temperature
|
Ambient Temperature
-10~+50¡É
|
Maintained Temperature
-5~+80¡É
|
|
cushion |
Standard
Orifice Type Built-in Reducing Speed Device |
Semi-standard
Reducing Speed Cushion |
|
Applied working oil |
regular mineral oil |
Rod End Thread Tolerance |
Grade KSB0214 |
Supporting or Fixing on Surface Type |
LA Type,LT Type,FA Type,FB Type,CA Type,TA Type,TB Type |
Note) |
1. In case of using the working speed during reverse, the standard pressure is 60kgf/§².
2. The working pressure is the highest set pressure on the relief side upon operation of cylinder.
3. The maximum permissible pressure is a pressure that can be practically applied maximally in consideration of the rigidity of cylinder including surge pressure.
4. The inner pressure is described as a test pressure with that the cylinder function should be sustained without any damage while the cylinder¡¯s pressure being lowered from the maximum permissible pressure
5. The minimum working pressure means a pressure that can make movement without any load as exerting input (the rod weight is excluded here).
|
Inside Diameter |
1T |
2T |
3T |
4T |
5T |
Cushion Length
|
1700 |
2500 |
3100 |
3100 |
3100 |
Note) |
Please, separately ask for the buckling of rods. For stroke above the limit, please contact us. |
|
Orifice type reducing speed cushion (shock absorber), whose stroke is short, was installed at both ends.
Also compact cushions were installed between the first and second shifts of the forwarding motions as well as between the first and second shifts of the reversing motion. |
|
Packing Material |
NBR |
URETHANE |
ºÒ¼Ò(VITON)
|
Regular Mineral Working Oil
|
|
|
|
Water-soluble Glycogel |
|
|
|
W/O Working Oil |
|
|
|
O/W Working Oil |
|
|
|
|
|
|
|
Fatty Acid Ester |
|
|
|
Note) 1. , is usable, while is not usable
2. For other working oils beside the regular one, please contact us |
|
|
¨ç |
¨è |
¨é |
¨ê |
¨ë |
¨ì |
¨í |
Supporting or Fixing on Surface Type
LA,LT,FA,FB,
TA,TB,CA
|
Series |
Rod End Thread Length
A:standard
B:Non-standard |
Cushion Type
B:Double Orifice Type
S:Both end reducing speed cushion |
Cylinder Stroke(mm) |
Port Position
(A,B,C,D,E,F,G,H) |
Air Removing Point
(A,B,C,D,E,F,G,H)) |
|
Model A |
Model B |
1T |
25 |
35 |
2T |
35 |
45 |
3T |
40 |
55 |
4T |
45 |
60 |
5T |
52 |
72 |
|
The standard position for piping is C and G, and the air ventilation position is A.
If you need a modification, please refer to the above picture. |
The standard position for piping is A and E, and the air ventilation position is C.
Make each pipe to pipe position or pipe to air ventilation position to be perpendicular or horizontal. If you need a modification, please refer to the above picture. |
|
|
|